CANON IR105 DRIVER FOR WINDOWS

Roller be checked in service mode. F F Close the hoper cover. These settings may be changed in service mode to suit the site of installa- tion: Check also to be sure that the main thermistor and the fixing roller are not away from each other. Does it change from 24 to 0 V when the Start key is pressed?

Uploader: Kishakar
Date Added: 10 June 2015
File Size: 63.45 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 69066
Price: Free* [*Free Regsitration Required]

Replace the delivery motor clock ur105 PI Slide the deck inside the copier. Check to make sure canon ir105 the solvent is fully dry.

F 4 Disconnect csnon main controller commu- canon ir105 cable [1] and the connector [2]. Cleaning the charging wire. E Main cause The fluorescent lamp is not mounted properly. F 5 Remove the 6 E-rings [1], 2 bearings [2], gear [3], and pin [4]; then, detach the clutch [5]. F 4 Peel off the Warning label [1] from the flexible cable [2]. canon ir105

These settings may be changed in service mode to suit the site of installa- tion: Canon ir105 plays its part through our compatible cartridge program. Using alcohol, clean the primary charging wire and grid wire.

F 11 Remove the 2 mounting screws [2] of the sensor unit [1]. When mounting the fan, be sure that the direction of air current is as indicated by the arrow. In general, the silicon gas vapor of silicone oil from the canon ir105 assembly tends to soil the corona charging wire, canon ir105 its life.

ON left deck lifter PS M6 inside the cartridge for 10 sec or more twice. Remove the face plate for the ADF connector from the copier.

Canon iR105 Service Manual

Be sure not to leave any droplets of water. The firm is actually specialized in optical and imaging product canon ir105. A roller is 2. OFF do not issue; default 1: Check the connection; if normal, replace the motor. Canon ir105 this time, use the index [3] on the latch plate as a it105.

Canon Inkjet Cartridges | Fast Shipping | Cartridge Sale

At this time, pay attention to the orientation of the wire cleaner. For details, see the User Guide. The sensor goes on and off, at times causing the motors and the like canon ir105 operate.

F 3 Canoj the connector [1], canon ir105 de- tach the internal delivery senor [2]. The reader controller PCB is faulty. F 7 When connection is done, the following screen will appear. Use it to select the source of paper for test printing. Use the screw [2] to adjust the position of the solenoid [1] so that the drive lever is fully pushed when the solenoid is ON i. Replace the CCD canon ir105. Condition An error exists on the FAX board. The wiring is faulty short circuit, open cir- cuit.

Fit canon ir105 ADF connector [1] into the socket found at the back canon ir105 the copier. While the ADF remains out of order, printing may be continued by discon- necting the lattice connector of the ADF, opening the ADF, and placing the original on the copyboard glass.

F Push in the face plate [1] lightly, and take out canin card reader base assembly canon ir105 from below.

프린터 스캐너 드라이버 다운로드 [1]

This is a normal condition, and will disappear when you turn off and then on the machine twice. Use it canon ir105 set the speed of the developing sleeve. ON 7-segment LED5 0: F 3 Disconnect the 3 connectors [1], and detach the cover switch assembly [2]. Close the toner cartridge cover [4]. It is recommended to back up the ir1055 whenever possible using the Service Support Cnon canon ir105 you canon ir105 updated the service mode settings or the user mode settings.

Check the delivery roller drive assembly.

Use it to set the sequence in which double-sided originals are read when the canon ir105 orientation detection mechanism is enabled. Canon ir105 sure that the feet of the machine will remain in contact with the floor, and the ma- chine will be kept level. Also, be sure that the con- nector in step 5 is firmly to the anti-reflection plate. Replace the side deck canon ir105 PCB.

Condition The motor clock signal is not detected for 2 sec or more after the fixing motor drive signal has been generated.

Close the front cover.

Canon ir105 the wiring for AC power, and check the connector for con- tact. Be sure to remove the accessories side paper deck, finisher, paper fold- ing unit when moving the machine into or ir1055 of the site of installation to prevent damage.

Front Deck left, right 1 Slide out the canon ir105, and loosen the 4 screws [2] and the 2 fixing screws it105 of the cassette front cover [1]. This includes camcorders, cameras, steppers, consumer printers, medical equipment and photocopiers.